TLP109 2009-04-01 1 toshiba photocoupler gaa ? as ired & photo ? ic TLP109 digital logic isolation line receivers power supply feedback control switching power supplies transistor inverters the toshiba TLP109 mini-flat coupler is a small-outline coupler suitable for surface-mount assembly. the TLP109 consists of a high-output-power gaa ? as light emitting diode optically coupled to a high-speed photodiode-transistor chip. the TLP109 is housed in the 6-pin so package and guarantees a creepage distance of 5.0 mm , a clearance of 5.0 mm and an insulation thickness of 0.4 mm. therefore, the TLP109 meets the reinforced insulation class requir ements of international safety standards. ? isolation voltage: 3750 vrms (min) ? switching speed: t p hl = 0.8 s, t p lh = 0.8 s (max) (@r l = 1.9 k ) ? ttl-compatible ? ul recognized :ul1577, file no.e67349 ? c-ul recognized :csa component acceptance service no. 5a, file no.e67349 ? vde under application : din en60747-5-2 pin configuration (top view) schematic construction mechanical ratings creepage distance: 5.0 mm (min) clearance: 5.0 mm (min) insulation thickness: 0.4 mm (min) toshiba 11 4l1 weight: 0.08 g (typ.) unit: mm 1: anode 3: cathode 4: emitter (gn d) 5: collector (output) 6: v cc v cc gnd v o i cc i o 6 5 4 3 i f v f shield 1 0.1 2.1 0.1 4.55 1 3 6 5 4 3.7 7.0 0.4 0.4 2.54 1.27 0.5 min 0.15 +0.25 -0.15 +0.25 -0.15
TLP109 2009-04-01 2 absolute maximum ratings (ta = 25c) characteristic symbol rating unit forward current (note 1) i f 20 ma pulse forward current (note 2) i fp 40 ma peak transient forward current (note 3) i fpt 1 a led reverse voltage v r 5 v output current i o 8 ma peak output current i op 16 ma supply voltage v cc ? 0.5 to 30 v output voltage v o ? 0.5 to 20 v detector output power dissipation (note 4) p o 100 mw operating temperature range t opr ?55 to 100 c storage temperature range t stg ?55 to 125 c lead solder temperature (10 sec.) t sol 260 c isolation voltage (ac,1 min., r.h. 60%) (note 5) bv s 3750 vrms note: using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operat ing temperature/current/voltage, etc. ) are within the absolute maximum ratings. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). (note 1) derate 0.36 ma / c above 70c. (note 2) 50% duty cycle, 1 ms pulse width. derate 0.72 ma / c above 70c. (note 3) pulse width 1 s, 300 pps. (note 4) derate 1.8 mw / c above 70c. (note 5) device considered a two ? terminal device: pins 1 and 3 shorted together, and pins 4, 5 and 6 shorted together.
TLP109 2009-04-01 3 electrical characteristics (ta = 25c) characteristic symbol test condition min typ. max unit forward voltage v f i f = 16 ma 1.50 1.64 1.85 v forward voltage temperature coefficient v f / ta i f = 16 ma D ?2 D mv /c reverse current i r v r = 3 v D D 10 a led capacitance between terminals c t v f = 0 v, f = 1 mhz D 60 D pf i oh (1) i f = 0 ma, v cc = v o = 5.5 v D 3 500 na i oh (2) i f = 0 ma, v cc = 30 v v o = 20 v D D 5 high level output current i oh i f = 0 ma, v cc = 30 v v o = 20v, ta = 70c D D 50 a detector high level supply current i cch i f = 0 ma, v cc = 30 v D 0.01 1 a current transfer ratio i o / i f i f = 16 ma, v cc = 4.5 v v o = 0.4 v 20 D D % low level output voltage v ol i f = 16 ma, v cc = 4.5 v i o = 2.4 ma D D 0.4 v isolation characteristics (ta = 25c) characteristic symbol test conditions min typ. max unit capacitance input to output c s v = 0 v, f = 1 mhz (note 5) D 0.8 D pf isolation resistance r s r.h. 60%, v s = 500 v (note 5) 510 10 10 14 D ac,1 minute 3750 D D ac,1 second, in oil D 10000 D v rms isolation voltage bv s dc,1 minute, in oil D 10000 D vdc switching characteristics (ta = 25c, v cc = 5 v) characteristic symbol test cir ? cuit test condition min typ. max unit propagation delay time (h l) t phl 1 i f = 0 16 ma r l = 1.9 k D D 0.8 s propagation delay time (l h) t plh 1 i f = 16 0 ma r l = 1.9 k D D 0.8 s common mode transient immunity at high output level (note 6) cm h 2 i f = 0 ma, v cm = 400 v p ? p r l = 4.1 k 5000 10000 D v / s common mode transient immunity at low output level (note 6) cm l 2 i f = 16 ma, v cm = 400 v p ? p r l = 4.1 k ?5000 ?10000 D v / s (note 6) cm l is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in the logic low state (v o < 0.8 v). cm h is the maximum rate of rise of the common mode voltage that can be sustained with the output voltage in the logic high state (v o > 2.0 v) (note 7) maximum electrostatic discharge voltage for any pins: 100 v (c = 200 pf, r=0)
TLP109 2009-04-01 4 test circuit 1: switch ing time test circuit test circuit 2: common mode tr ansient immunity test circuit v o i f 5 v 1.5 0 v ol t plh t phl 1.5v pw = 100 s duty ratio = 1/10 i f monitor pulse input output monitor v o 100 v cc = 5 v 1 3 4 5 6 r l i f v o v cm 400 v 0 v 90% 5 v 2 v 0.8 v v ol t r t f 10% v o (i f = 16 ma) (i f = 0 ma) i f pulse generator z o = 50 v cm output monitor v o v cc = 5 v 1 3 4 5 6 r l s)(t 320(v) cm s)(t 320(v) cm r l , r h = =
TLP109 2009-04-01 5 specification for embossed?tape packing (tpl)(tpr) for so6 coupler 1. applicable package package product type so6 mini-flat coupler 2. product naming system type of package used for shipment is denoted by a symbol suffix after a produc t number. the method of classification is as below. (example) 3. tape dimensions 3.1 specification classification are as shown in table 1 table 1 tape type classification tape type classification quantity (pcs / reel) tpl l direction 3000 tpr r direction 3000 3.2 orientation of device in relation to direction of tape movement device orientation in the recesses is as shown in figure 1. figure 1 device orientation TLP109 (tpl) device name tape type direction of tape l direction r direction
TLP109 2009-04-01 6 3.3 empty device recesses are as shown in table 2. table 2 empty device recesses standard remarks occurrences of 2 or more successive empty device recesses 0 within any given 40-mm section of tape, not including leader and trailer single empty device recesses 6 devices (max) per reel no t including leader and trailer 3.4 start and end of tape the start of the tape has 50 or more empty holes. the end of tape has 50 or more empty holes and two empty turns only for a cover tape. 3.5 tape specification (1) tape material: plastic (protection against electrostatics) (2) dimensions: the tape dimensions are as shown in figure 2 and table 3. figure 2 tape forms table 3 tape dimensions unit: mm unless otherwise specified: 0.1 symbol dimension remark a 4.2 D b 7.6 D d 5.5 center line of indented square hole and sprocket hole e 1.75 distance between tape edge and hole center f 8.0 cumulative error (max) per 10 feed holes g 4.0 cumulative error (max) per 10 feed holes k 0 2.8 internal space +0.1 -0.3 +0.1 -0.3 0.3 0.05 3.15 0.2 k 0 g f 1.6 0.1 a e d b 12.0 0.3 1.5 +0.1 ?0
TLP109 2009-04-01 7 3.6 reel (1) material: plastic (2) dimensions: the reel dimensions are as shown in figure 3 and table 4. figure 3 reel form table 4 reel dimensions unit: mm symbol dimension a 380 2 b 80 1 c 13 0.5 e 2.0 0.5 u 4.0 0.5 w1 13.5 0.5 w2 17.5 1.0 4. packing either one reel or five reels of photoc oupler are packed in a shipping carton. 5. label indication the carton bears a label indicating the product num ber, the symbol representing classification of standard, the quantity, the lot num ber and the toshiba company name. 6. ordering method when placing an order, please spec ify the product number, the tape type and the quantity as shown in the following example. (example) e w1 w2 a b c u TLP109 ( tpl ) 3000 p cs device name tape type quantity (must be a multiple of 3000)
TLP109 2009-04-01 8 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively ?toshiba?), reserve the right to make changes to the in formation in this document, and related hardware, software a nd systems (collectively ?product?) without notice. ? this document and any information herein may not be reproduc ed without prior written permission from toshiba. even with toshiba?s written permission, reproduc tion is permissible only if reproducti on is without alteration/omission. ? though toshiba works continually to improve product?s quality and reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for prov iding adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a ma lfunction or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. before creating and producing des igns and using, customers mus t also refer to and comply with (a) the latest versions of all re levant toshiba information, including without limitation, this d ocument, the specifications, the data sheets and applic ation notes for product and the precautions and conditions set forth in the ?tosh iba semiconductor reliability handbook? and (b) t he instructions for the application that product will be used with or for. custome rs are solely responsible for all aspects of t heir own product design or applications, incl uding but not limited to (a) determining th e appropriateness of the use of this product in such design or applications; (b) evaluating and det ermining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. toshiba assumes no liability for customers? product design or applications. ? product is intended for use in general el ectronics applications (e.g., computers, personal equipment, office equipment, measur ing equipment, industrial robots and home electroni cs appliances) or for specif ic applications as expre ssly stated in this document . product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality a nd/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or se rious public impact (?unintended use?). unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic s ignaling equipment, equipment used to control combustions or explosions, safety dev ices, elevators and escalato rs, devices related to el ectric power, and equipment used in finance-related fields. do not use product for unintended use unless specifically permitted in thi s document. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is pres ented only as guidance for product use. no re sponsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. ? a bsent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability whatsoever, including without limitation, indirect, co nsequential, special, or incidental damages or loss, including without limitation, loss of profit s, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? gaas (gallium arsenide) is used in product. gaas is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose gaas in product. ? do not use or otherwise make available product or related so ftware or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or m anufacturing of nuclear, chemical , or biological weapons or missi le technology products (mass destruction w eapons). product and related software and technology may be controlled under the japanese foreign exchange and foreign trade law and the u.s. expor t administration regulations. ex port and re-export of product or related software or technology are strictly prohibited exc ept in compliance with all applicable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regula tions that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losses occurring as a result o f noncompliance with applicable laws and regulations.
|
